Wiring Diagram Guide
Get Your Engine Running
Learn how to wire your Corris Rivett's electrical system. Covers battery, starter, alternator, ignition, and the firing order 1-3-4-2.
Electrical System Overview
The Corris Rivett has five main electrical systems that must be properly connected for the engine to start. Understanding each system will help you troubleshoot problems quickly.
Power System (12V)
Battery provides power to all electrical components
Charging System
Alternator recharges the battery while engine runs
Starting System
Starter motor cranks the engine to start
Ignition System
Distributor and spark plugs ignite the fuel mixture
Auxiliary Circuits
Lights, gauges, horn, and other accessories
Video Tutorials
These comprehensive video tutorials will walk you through the entire wiring process step by step.
Complete Wiring Tutorial
Full guide covering all electrical connections from start to finish
Wiring & First Engine Start
Step-by-step wiring with first successful engine start demonstration
Pro Tip
Key Wiring Steps
Follow these essential steps to get your electrical system working:
1. Battery Connection
Connect the battery terminals correctly. Red (+) goes to positive, black (-) to ground.
Wrong polarity can damage electrical components!
2. Starter Motor
Connect the thick cable from battery positive to the starter motor. The starter solenoid gets power from the ignition switch.
The starter motor is located at the bottom rear of the engine.
3. Alternator
Connect the alternator output wire to charge the battery. Without this, your battery will drain.
Also connect the exciter wire for the charge indicator light.
4. Ignition System
Wire the distributor and coil. Connect spark plug wires in the correct firing order.
Firing order is critical - incorrect order will prevent starting.
5. Fusebox
Connect the fusebox for protection. This powers lights, gauges, and accessories.
Fusebox is located under the dashboard on the driver's side.
Firing Order: 1-3-4-2
The spark plug firing order is crucial for engine operation. Connect the distributor wires in this exact sequence:
Starting from cylinder 1 (front), follow the firing order clockwise on the distributor cap.
Important
Common Wiring Mistakes
Avoid these frequent errors that prevent engine starting:
| Problem | Symptom | Solution |
|---|---|---|
| Bad Ground Connection | Starter clicks but doesn't turn, weak lights | Check battery negative terminal and engine ground strap |
| Wrong Spark Plug Wire Order | Engine cranks but won't start, backfires | Verify firing order 1-3-4-2 on distributor cap |
| Loose Starter Wire | Nothing happens when turning key | Tighten connections at starter solenoid |
| Alternator Not Connected | Battery drains quickly, charge light stays on | Connect alternator output and exciter wires |
| Missing Fusebox Connection | No lights, gauges don't work | Connect main power wire to fusebox |
Troubleshooting
If your car won't start, check these common issues:
Engine Doesn't Crank
- Battery charged?
- Battery terminals tight?
- Starter motor wire connected?
- Ignition switch working?
Engine Cranks But Won't Start
- Fuel in tank?
- Spark plug wires correct order?
- Distributor cap secure?
- Coil wire connected?
Battery Drains Quickly
- Alternator connected?
- Belt tight on alternator?
- Lights left on?
Frequently Asked Questions
What's the firing order for the Corris Rivett?
The firing order is 1-3-4-2. Cylinder 1 is at the front of the engine. Follow this order when connecting spark plug wires to the distributor cap.
Where is the fusebox located?
The fusebox is under the dashboard on the driver's side. You need to connect it for lights, gauges, and accessories to work.
My car cranks but won't start - what should I check?
Check: 1) Spark plug wire order (1-3-4-2), 2) Fuel in tank, 3) Distributor cap connection, 4) Coil wire. These are the most common causes.
Do I need the fusebox for the engine to start?
No, the engine can start without the fusebox connected. However, you won't have lights, gauges, or accessories until it's wired.